Enterasys-networks Fast Network 10 Uživatelský manuál Strana 75
- Strana / 132
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Using LCM to Manage the FN10
Fast Network 10 User Guide Page 4-15
4.5 USING LCM TO MANAGE THE FN10
The LCM commands that enable you to manage the FN10 include:
• Disable
• Enable
• Ipaddr
• Community
• Baud
• Reboot
These LCM commands are described in the sections that follow.
4.5.1 Disabling a Port
There can be times when you need to disable a specific Ethernet port, for
example, after you have determined that there is faulty equipment.
Disabling a port effectively stops all bridging functions for that port.
Disabled ports do not accept SNMP packets, and therefore cannot
communicate with an NMS.
To disable a port, or port range, at the LCM prompt:
1. Type
disable <PORT-RANGE>
For example, disable 7-9 would disable ports 7, 8, and 9.
LCM responds:
Once an Ethernet port is disabled, it will be disabled until you enable it
again. Resetting the FN10 will not enable a port that has been disabled.
Port 7: Disabled
Port 8: Disabled
Port 9: Disabled
- FAST NETWORK 10 1
- USER GUIDE 1
- Fast Network 10 User Guide i 3
- CONTENTS 7
- FastNET 10 User Guide vii 9
- Contents 10
- CHAPTER 1 11
- INTRODUCTION 11
- 1.2 GETTING HELP 12
- 1.3 DOCUMENT CONVENTIONS 13
- 1.4 RELATED DOCUMENTATION 14
- 1.5 OVERVIEW 14
- Overview 15
- 1.5.1 FN10 Architecture 16
- 1.5.3 FN10 Filtering 20
- 1.5.4.1 FN10 Trunking 21
- Chapter 1: Introduction 22
- 1.5.4.3 Virtual Workgroups 24
- 1.6 LOCAL CONSOLE MANAGER 25
- Reference Card 26
- 1.6.2 Basic LCM Commands 27
- 1.6.2.1 Help 28
- 1.6.2.2 Erase 28
- 1.6.2.3 Exit 29
- 1.6.2.4 Logout 29
- 1.6.2.5 Traplog 29
- CHAPTER 2 31
- UNPACKING AND INSTALLING 31
- YOUR FN10 31
- Port B Port A 32
- FN10 Panels 33
- 2.2 INSTALLING THE FN10 34
- Installing the FN10 35
- FN10 > prompt 37
- ETHERNET MODULE 39
- CHAPTER 3 43
- CONFIGURING YOUR FN10 43
- • Displaying trunking status 44
- • Assigning a community name 44
- 3.1 ASSIGNING IP ADDRESSES 45
- 3.1.1 Displaying IP Addresses 46
- 3.1.2 Deleting an IP Address 46
- 3.1.3 Changing a Subnet Mask 46
- 3.2 ENABLING BRIDGING 47
- 3.3 DISABLING BRIDGING 48
- 3.5 ENABLING TRUNKING 49
- Trunk Groups 50
- 3.6 DISABLING TRUNKING 51
- FN10 > trunk 2-4 52
- Displaying Trunking Status 53
- Workgroup A 54
- Workgroup B 54
- Assigning a Community Name 57
- RCM Reference Guide 58
- 3.11 MODIFYING MIB VARIABLES 59
- 3.11.1 System Contact 59
- 3.11.2 System Name 59
- 3.11.3 System Location 59
- 3.11.5 Aging Parameter 60
- CHAPTER 4 61
- MONITORING AND MANAGING 61
- 4.2.1 Pseudo Filters 63
- 4.2.2 Gathering Statistics 63
- 4.2.3 System Statistics 63
- FN10 Statistics 65
- 4.2.5 MAC Statistics 66
- 4.2.7 SNMP Statistics 67
- 4.3.1 Displaying Status 69
- 4.4 MANAGING THE FN10 74
- 4.5.1 Disabling a Port 75
- 4.5.2 Enabling a Port 76
- 4.5.2.1 noRIP Option 76
- 4.5.3 Changing a Subnet Mask 77
- 4.5.5 Setting the Baud Rate 78
- 4.5.6 Setting a Reboot Time 79
- CHAPTER 5 81
- FN10 FILTERS 81
- 5.1.1 Source Address Filter 83
- 5.2 PORT FILTERS 84
- 5.2.1 Configurable Fields 85
- 5.2.1.1 Pseudo Filtering 86
- 5.2.1.2 Filter Links 86
- Port Filters 87
- Adjoining Network Segment 91
- Computers that cannot 93
- PERFORMANCE 96
- LAN 4LAN 3 97
- 5.5 CONFIGURING A PORT FILTER 99
- Chapter 5: FN10 Filters 100
- Configuring a Port Filter 101
- 5.5.1 Modifying a Port Filter 102
- 5.5.2 Deleting a Port Filter 103
- CONSIDERATIONS 103
- CHAPTER 6 105
- 6.1.1 Power-up LED Sequence 106
- 6.1.2 Specific Power-up Tests 106
- 6.3 DIAGNOSTIC LOOPBACK TESTS 107
- 6.3.1 Loopback Tests 108
- 123456 7 111089 109
- Reset Ready 109
- 6.5 TROUBLESHOOTING 111
- 6.5.1 FN10 Does Not Power Up 111
- 6.5.2 Connectivity Problems 111
- 6.5.3 FN10 Has Rebooted 112
- APPENDIX A 113
- TECHNICAL SPECIFICATIONS 113
- Bridging Technologies 114
- Address Table Size 114
- Management Support 114
- Certification 114
- A.3 10BASE-T PIN ASSIGNMENTS 115
- A.4 STRAIGHT-THROUGH WIRING 116
- A.5 CROSSOVER WIRING 117
- A.6 5 - 4 - 3 RULE 117
- APPENDIX B 119
- GLOSSARY 119
- Appendix B: Glossary 120
- Numerics 129
Související produkty a manuály pro Hardware Enterasys-networks Fast Network 10
Hardware Enterasys-networks 802.11 Uživatelský manuál
(202 stránky)
(202 stránky)
Hardware Enterasys-networks 1G58x-09 Uživatelský manuál
(808 stránky)
(808 stránky)
Hardware Enterasys-networks 8000/8600 Uživatelský manuál
(142 stránky)
(142 stránky)
Hardware Enterasys-networks XSR-3020 Uživatelský manuál
(110 stránky)
(110 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce