Enterasys-networks XSR-3020 Uživatelský manuál stáhnout pdf (Strana 44)

Connecting Cables

2-12 Hardware Installation

6. Attach the power supply cord to the connector at the rear of the XSR, as shown in Figure 2-19

and plug in the country-specific power cord connects to a wall socket. The XSR will power up.

Figure 2-19 Connecting Power Supply Cord

You are now ready to configure the software and initialize the XSR. Continue with Chapter 3,

Software Configuration.

LINE

100~125V~1.25A

200~240V~0.65A

50/60Hz

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 109 110

X-Pedition 1
Security Router 1
Industry Canada Notices 5
Class A ITE Notice 5
Clase A. Aviso de ITE 5
Klasse A ITE Anmerkung 5
orcontact 6
(Circuit Modules) 7
(Circuit Breakers) 7
VCCI Notice 8
BSMI EMC Statement — Taiwan 8
Declaration of Conformity 8
Australian Telecom 9
Contents 13
Appendix A: Specifications 15
About This Guide 17
Getting Help 19
Overview 21
PSTN (for PPP) 22
ETH2ETH1 23
Operating System 24
Industry-common CLI 24
IP Protocol 24
IP Routing 25
SNMP and Statistics Gathering 25
Security 26
Frame Relay 26
System Description 27
XSR Getting Started Guide 1-7 27
Quality of Service (QoS) 28
Virtual Private Network (VPN) 28
GRE over IPSec 29
Dial Service 30
Dial Backup 30
Installation Overview 31
1-12 Overview 32
Hardware Installation 33
2-2 Hardware Installation 34
XSR Getting Started Guide 2-3 35
2-4 Hardware Installation 36
XSR Getting Started Guide 2-5 37
2-6 Hardware Installation 38
Connecting Cables 39
SECURITY ROUTERS 40
XSR Getting Started Guide 2-9 41
Figure 2-16 42
Figure 2-18, respectively 43
Software Configuration 44
Initializing XSR Software 46
3-2 Software Configuration 46
XSR Getting Started Guide 3-3 47
Setting the Clock 51
Configuring the LAN Ports 52
Configuring the WAN Ports 52
BRI Leased Line 53
BRI Leased Frame Relay 53
BRI Switched Line 54
Firewall Sample Configuration 56
Setting Up RIP Routing 58
Configure OSPF Routing 59
3-16 Software Configuration 60
Viewing Your Configuration 61
3-18 Software Configuration 62
Site regional router 64
Configure Users and Passwords 66
Configure LAN Interface 66
Configure Quality of Service 66
Apply QoS 68
Configure More Access Lists 68
Configure DHCP/BOOTP Relay 69
Configure SNMP 70
Set Up IKE Phase I Security 71
Create a Transform Set 72
Configure Crypto Maps 72
3-30 Software Configuration 74
XSR Rebooting Characteristics 76
Reboot Triggers 77
Cause Boot Type 77
3-34 Software Configuration 78
Bootrom Monitor Mode Commands 79
3-36 Software Configuration 80
3-38 Software Configuration 82
3-40 Software Configuration 84
3-42 Software Configuration 86
Specifications 87
Short-haul MTRJ 88
Pin 1 Pin 5 90
Pin 6 Pin 9 90
Pins not shown are unused 96
RX In TX Out 99
G.703 Balun 99
Model 460 MC 99
Regulatory/Safety Compliance 101
ALARM LOS 101
ENABLE LOF 101
Port 0 Activation LED 102
Port 1 Activation LED 102
Pin 8Pin 1 102
Transmit Pair Termination 103
Port 0 Port 1 103
Port 1Port 0 103
Receive Pair Termination 103
NIM1 NIM2 107
LED State Function 108
Index-2 110

Komentáře k této Příručce

Žádné komentáře

Enterasys-networks XSR-3020 Uživatelský manuál Strana 44

Komentáře k této Příručce

Související produkty a manuály pro Hardware Enterasys-networks XSR-3020